Trinity

Trinity Support

Repeatit Trinity is a family of high performance hybrid-wireless point to point (PtP) and

point to few (PtF) united with a unique cloud ecosystem

Trinity 800 Series

Documents
Release Notes
Version 2.6.0.9     Release Date: 2017-06-02
  • Corrected a bug causing the SNMP Agent not to be started
Version 2.6.0.8     Release Date: 2017-02-13
  • Changed the radio protocol to support multipoint.
  • Fixed a bug causing short disruptions of traffic at random time. Disruption time between 3-30s.
Version 1.6.0.7     Release Date: 2017-02-03
  • Corrected a bug with Google Map API, caused the map not to show in the location dialog.
  • Corrected how statistics from ethernet chip was reported.
Version 1.6.0.6     Release Date: 2017-01-05
  • Added possibility to upload/download configuration files.
Bugs, Issues & Limitations
Known issues and Limitations in Current Version (X.X.X.X)

After upgrading, refresh the page for true results. (Repeatit products tested & supported on Google Chrome browsers.)

If you are using SyncMaster, it has to be upgraded to the latest release too when the Trinity will be upgraded to the new software.

Latest firmware

We engineer our firmware updates to work across all Trinity 800 series platforms.

NEW MAJOR VERISON:
Both Master and client needs to be upgraded, version 2.x.x.x is not compatible with 1.x.x.x

SW version 2.6.0.9

2017-06-02: Release of version 2.6.0.9

– Latest Firmware Trinity800 2.6.0.9

Trinity 200 & 300 Series

Important Information

This version of Trinity is not compatible with the old Trinity version, both units in a link must be upgraded.

This image is valid for both 200-Series and 300 Series of Trinity.

 

NOTE: Always start the upgrade with the remote node.

 

NOTE: A bug as been found in late versions of software, it relates to the alignment buzzer. If buzzer is enabled and this is also saved to the flash the unit might end-up in a endless reboot cycle.  Alignment buzzer can still be used but the setting to enabled should not be saved to the flash. A fix is currently under test and new release with a fix will be 2.0.0.11 scheduled for 12 January 2015.

 

NOTE! Due to a memory leak in all versions before 2.0.0.0 of Trinity software it is recommended to perform a reboot of the units before upgrading. Not doing this can cause a failure in the upgrade procedure.

Documents
Release Notes
Version 3.0.1.27 (2017-02-15)
  • Resolved a problem with internal communication in unit, could cause status page to be empty.
  • Fixed a problem in MultiFlex mode, borrow of timeslots was not evenly distributed between clients when configured with few fix slots and many borrow slots.
  • Fixed a problem in communication with cloud server, unneeded data was sent to cloud.
  • Fixed a problem when changing LinkID, change did not take effect directly.
  • Added possibility to download/upload configuration files.
Version 3.0.1.25 (2016-10-11)
  • Resolves a problem when using dynamic time-slot assignment in MultiFlex mode. Caused the time-slots not to be divided equal between clients.
  • Fixed a problem in status page where max theoretical bandwidth could get to many decimals.
  • Improved the fix for the problem with blank status page.
  • Fixed a problem with PacketHeal, could cause a hang and reboot under heavy load and asymmetrical time division with high upload capacity.
Version 3.0.1.23 (2016-09-26)
  • Resolved a problem in MultiFlex mode where the modulation used by the Master against one or more clients got stucked at the lowest allowed modulation.
Version 3.0.1.22 (2016-09-22)
  • Corrected a problem where links could have more retransmissions than necessary. Problem was caused by a low margin in the timing of acknowledgement.
Version 3.0.1.21 (2016-08-25)
  • Corrected a problem reported in 3.0.1.20 where the Status page after a variable time showed up blank. Problem caused by a data struct defined to small for the amount of clients. Depending on the amount of traffic the time before the problem showed up was variable. Increased traffic increased the size demand and eventually the data struct was to small.
Version 3.0.1.20 (2016-08-19)
  • Increased number of supported clients in MultiFlex mode to 31.
Version 3.0.1.19 (2016-07-19)
  • Updated access to GoogleMaps when picking coordinates of unit. Google demands the use of an API-Key.
  • Fixed problem with rate algorithm introduced in version 3.0.1.15
  • New feature, dynamic allocation of timeslots.
Version 3.0.1.15 (2016-06-17)
  • Changed the text when a chain on extension channel has no signal, inform user that extension channel is not valid with current modulation
  • Modified packet heal algorithm.
  • Fix a problem with signal level readings, caused the presented signal value to sometimes be aprox 10dB lower than actual.
  • Cleaned up available channels when running in 40MHz mode
  • Added Mexico and Colombia.
  • Enabled P2P Master mode in Trinity216SU
  • Fix a problem with SpeedTest, before it sent after 5min all traffic as broadcast traffic.
Version 3.0.1.13 (2016-03-10)
  • Added an new msg sent to Cloud server. Improves how to visualize MultiFlex in Cloud Server.
Version 3.0.1.12 (2016-02-26)
  • Increased number of DICCOVERY_ACK frames sent from 2 to 4/s, improves link stability when link quality is bad.
  • Adjusted so that broadcast is limited by global max rate set on Master.
Version 3.0.1.10 (2016-01-29)
  • Adjusted number of ACK frames sent. Improves delivery of packets and reduces duplicates.
  • Improved multicast handling.
  • Adjusted the rate algorithm.
  • Resolved a problem where packets where accounted for on the wrong rate.
  • Resolved a problem with VLAN taged packets, caused problem communicating with unit over ethernet interface.
Version 3.0.1.7 (2015-12-21)
  • Resolved a memory leak problem with SNMP. Using SNMP for a longer period of tome could cause memory resources to be low and the link could end up in a repeating up/down state.
  • Improved synchronization stability.
  • Improved handling of multipoint clients.
  • Added reminder to check NTP settings when using Cloud service.
  • Added a “Debug dump” button to be able to dump information that can help Repeatit Support on links.
  • Status page update, the status page has been updated to better show local/remote side.
Version 3.0.0.7 (2015-08-31)
  • Improved link synchronization at 5 & 10MHz channel BW.
  • Implemented Peer2Peer communication between nodes in MultiFlex mode.
  • Hide extension channel RSSI when not using 40MHz channel BW.
  • Bug fix, high load of broadcast/multicast could cause reboots.
  • Bug fix, when link got connected it made also a disconnect increasing the time before link was up.
  • Bug fix, at some points the link could not come up due to a fault in the modulation scheme, this eventually triggered a reboot of the units.
Version 3.0.0.5 (2015-07-15)
  • MultiFlex release.
  • Improved time-slot handling, lower latency.
  • Improved stability
Version 2.0.0.17 (2015-02-20)
  • Fix a bug causing the pkt/s to be limited for 5MHz & 10MHz channels
  • Added support for Australia.
  • Added signal level in dBm in the status bars.
  • Removed a limit of highest available modulations for Trinity316S.
  • Added info received from remote unit on status page, RSSI level + basic stats.
  • Changed the guard interval to always allow short, use of short/long is handled by rate algorithm.
  • Fix a bug related to setting the default GW, it was impossible to set the GW by it self.
  • Cosmetic changes to the status page and admin page. For example moved the Interface MAC address info from Status page to admin page.

 

Version 2.0.0.11 (2015-01-13)
  • Fix a bug related to alignment buzzer, if buzzer was enabled and saved to flash this could cause repeated reboots of unit during startup.

 

Version 2.0.0.10 (2014-12-11)
  • Fixed a problem with CAC, custom time did not show up all the times.

 

Version 2.0.0.9 (2014-12-08)
  • Fixed a problem when changing password, login page was reloaded before it was possible to enter new password.

 

Version 2.0.0.8 (2014-12-03)
  • Added Repeatit private SNMP mib.
  • Enabled use of buzzer for alignment.
  • Enabled bandwidth control.
  • Fixed a problem with not showing all channels on 3.5GHz
  • products.
  • Corrected a bug causing the presented signal levels to be wrong at low load.

 

Version 2.0.0.5 (2014-08-28)
  • Lowered the number of SyncFrames sent to SyncMaster.
  • Resolves a problem in SyncMaster when many units are connected to the SyncMaster.
  • Fixed a performance issue added when SyncMaster support was implemented. High load of traffic could cause a leak of buffers used for received packets and eventually lead to a link failure watchdog reset.
  • Fixed a bug in boot-up code that could lead to a failure in the boot-up with the result of many reboots after each other. This problem has been seen only on units from first half of 2012.
  • Cosmetic changes in Webinterface.

 

Version 2.0.0.3 (2014-08-08)
  • Added support for old 300-Series units.
  • Improved watchdog functionality.
  • Changed names on parameters in web-interface.

 

Version 2.0.0.0
  • Do not send packets to interface that is not ready, could cause a reboot of unit.
  • Fix a bug causing the client not to trigger a link loss event. Could cause the link to be down until client unit was rebooted.
  • Added a “show SyncMasters” button to easy find available SyncMasters.
  • Added a show links button to Clients.
  • Added a garbage collection routine to free available memory, reduces problems with to low memory.
  • Tweaked the AutoRate algorithm
  • Added possibility to set lowest rate to be used.
  • Improved communication with SyncMaster, makes sync more accurate.
  • Changed status page to always show “Show more” information.
  • Fix a problem with communication with Repeatit Cloud Server, a leak of sockets caused unit not to connect to server after some time.
  • Improved stability.

 

Version 1.9.99.12
  • Added feature to reduce noise impact.
  • Fix a bug causing a radar detection on Client unit not to communicated to the Master unit.

 

Version 1.9.99.11
  • Added support for SyncMaster, Master unit can now be synchronized against a SyncMaster unit.
  • Improved autorate algorithm
  • Fix a bug with upgrade to PLUS version through Cloud mgmt system.

 

Version 1.9.99.10
  • Increased resources for ethernet driver, could in some cases cause reboot of the unit.
  • New feature, it is now possible to configure the level om reordering of packets that gets out of order due to retransmissions.
  • Fix a bug causing the unit not to use 40MHz even if configured for it.

 

Version 1.9.99.9
  • Fix a bug causing loss of frames when auto-rate algoritm changed rate.
  • Changed rate implementation so that it always uses auto-rate, but with possibility to set the max rate the algoritm can use.
  • Updated rate table in web interface to correlate to rates used by auto-rate algoritm.
    New feature, make it possible to configure the QoS priority rules.

 

Version 1.9.99.6
  • Resolved issue with rebooting units:
  • Two independent sources has reported that using UK 5.8 country code could make a master unit go into a continuously reboot cycle. We have been able to reproduce the problem and it happens only on Master units and it only happens after a reboot. This means that after changing to UK 5.8 the unit will work if only Apply has been used. But if unit is rebooted it will start rebooting.
  • A fix is currently tested and new version 1.9.99.5 will come out soon.
  • If you have a link running on 1.9.99.4 or earlier make sure you do not use UK 5.8, reconfigure it to use another frequency band.
    Solved a bug created in 1.9.99.5 related to getting more information about retries.

 

Version 1.9.99.5
  • Treat Multicast traffic as unicast traffic, improves capacity of multicast traffic.
  • Added internal possibility to get more info about retransmissions.

 

Version 1.9.99.4
  • Resolved 2014-02-06 We have had one report that during high full duplex load of the link the link can go down. If high load is on when link tries to go up again it can cause a reboot of one of the units.
  • Workaround: Disable the high load, this will make the link come up again without possible reboot.
  • Solution: Possible cause has been identified, correction is implemented and currently under test. New beta 1.9.99.4 is scheduled for 2014-02-07.
  • Changed name from Slave to Client in all text presented in webinterface of unit.
  • Small performance improvements that do not affect stability.

 

Version 1.9.99.3
  • Disable the possibility to run single stream.
  • Removed unused parameters showing up in Cloud and RCS mgmt-systems.
  • Fix a problem with status LED, not showing RSSI level.
  • Make the slave unit not to follow the master txrate, it is now possible to configure different bitrates on Master and Slave.

 

Version 1.9.99.2
  • First released version
Bugs, Issues & Limitations
Known issues and Limitations in Current Version (3.0.1.15)
  • Assymetrical bandwidth is limited to 75/25.
  • When Changing the LinkId on a Client client will still connect to the old LinkID. If a Client shall be moved to another LinkID change the LinkID and let it come back online. Save the settings and reboot the Client.
Limitations in Current Version (2.0.0.0)
  • Assymetrical bandwidth is limited to 75/25. 80/20 is scheduled for release 2.1.0.0
  • Autodistance feature is not implemented, scheduled for release 3.0.0.0
  • Multipoint support, scheduled for release 3.0.0.0

 

Bugs In Current Version
  • None

 

Reported Issues (Not Bugs)
  • 2014-02-07 After an upgrade the statistics is not shown correctly in the web-interface. Excessive retries are showing total packets transmitted.
    This is not a bug, a couple java-scripts that are used in the web-interface has been updated and the web browser that is used does not refresh the cache it keeps using the old scripts.Solution, force the web browser to reload cache.
Videos

Latest firmware

We engineer our firmware updates to work across all Trinity 200 & 300 series platforms.

SW version 3.0.1.27

2017-02-15: Release of version 3.0.1.27.

Version 3.0.1.27

  • Resolved a problem with internal communication in unit, could cause status page to be empty.
  • Fixed a problem in MultiFlex mode, borrow of timeslots was not evenly distributed between clients when configured with few fix slots and many borrow slots.
  • Fixed a problem in communication with cloud server, unneeded data was sent to cloud.
  • Fixed a problem when changing LinkID, change did not take effect directly.
  • Added possibility to download/upload configuration files.

Current version is 3.0.1.27 (MultiFlex Release):
Latest Firmware (V3.0.1.27)
– SNMP MIB File

Trinity 116

Documents
Release Notes

Release notes and older firmware versions. Unless instructed otherwise, it is always recommended to use the latest firmware version.

Trinity-100 1.5.0.15 – 2015-03-12
  • Fixed a problem when apply features, did not show correct name.
  • Added new country codes..
  • Reduced queue size of radio- and ethernet-interface, could cause a problem with resources and eventually a crash with reboot.
 
Trinity-100 1.5.0.12 – 2014-04-03
  • Corrected available choices of txpower.
  • Corrected a bug causing available txRates not to be show when using 10MHz channel bandwidth.
  • Fixed available channels for Turkey Country code.

 

Trinity-100 1.5.0.11 – 2014-02-03

Download – (2.91 MB)

  • Corrected a bug causing the throughput in webinterface to be wrong.
  • Fixed a bug causing a unit connected to RCS to reboot if RCS connection was lost for more than 2min.

 

Trinity-100 1.5.0.10 – 2013-12-03

Download – (2.91 MB);

  • Changed Turkey country code to use ETSI DFS.

 

Trinity-100 1.5.0.8 – 2013-11-04
  • Corrected a bug causing 10MHz channel bandwidth to only use 20MHz channel spacing.
  • Allow QinQ sized frames to pass bridge.
  • Fixed a bug in Trinity100 where it was impossible to change channel width on Trinity100-Series slaves.
  • Changed units in webinterface from Mbyte/s to Mbit/s.

 

Trinity-100 1.5.0.7 – 2013-06-25

Download

  • Added support for 10MHz channels on Trinity100-Series.
  • Fixed a problem with distance when using 5 and 10MHz channels.
  • Added support for new model supporting 4.9GHz.
  • Changed from dBm to dB for RSSI values.

 

Trinity-100 1.5.0.5 – 2013-03-13


Download

  • Added support for Brazil market.
  • Fixed a problem with DFS, now mark 40MHz channels correctly.
  • Fixed some problems with using fixed ethernet speed.

 

Trinity-100 1.4.1.3 – 2012-07-25

Download

  • Corrected a bug where bandwidth limitations could limit the traffic due to a step in time caused by NTP protocol.
  • Make link transparent also for traffic related to switches and bridges when STP is turned of. This kind of traffic was “consumed” by the unit. Causing some applications not to work properly.
  • Corrected a bug causing the signal strength presented in webinterface to be wrong.

 

Trinity-100 1.4.1.0 – 2011-11-16
  • The web interface displays RSSI per chain.
  • Wrong clock rate caused distance calculations to be wrong at large values.
  • The unit could fail to re-connect to Repeatit Network if nameservers were unreachable.
  • Improved fixed radio rate operation.
  • The unit could fail to select a new channel when switching between auto indoor and auto outdoor.
  • The radio bandwidth limitation feature could result in that no traffic passed through the link.

 

Trinity-100 1.4.0.1 – 2011-10-03

Download

  • Repeatit Cloud Network communication improvements.

 

Trinity-100 1.4.0 – 2011-09-01

Download

  • Configurable Ethernet speed for Trinity-100 Series.
  • Fine grain bandwidth limitation support, allows more precise control of how much real throughput that is allowed over the radio.

 

Trinity-100 1.3.3 – 2011-08-19

Download

  • 10MHz channel bandwidth did not work properly.
  • Minor web interface fixes. Select location button did not work properly in certain browsers. The firmware upgrade could get stuck if the upload failed.

 

Trinity-100 1.3.2 – 2011-08-01

Download

  • The unit could fall back to auto channel selection upon boot when using a non-ETSI regulatory domain.

 

Trinity-100 1.3.1 – 2011-07-06

Download

  • Multiple web interface fixes for Internet Explorer.
  • Repeatit Network interface and communication improvements.
  • Fix for unnecessary link disconnection. The link could disconnect during apply even if no radio related parameter had been changed.
  • Improved icons for the web interface.

 

Trinity-100 1.3.0 – 2011-06-22

Download

 
  • Support for Repeatit Network – free cloud based management system.
  • STP (Spanning Tree Protocol) support have been added.
  • DNS server configuration support.
  • NTP support for unit clock synchronization.
  • Interactive map in the web interface for easier longitude/latitude coordinate selection.
  • All web interface field entries are now completely UTF-8 safe.
  • Channel selection list could be wrong when running with a non-ETSI regulatory domain together with the RCS.

 

Trinity-100 1.2.4 – 2011-05-12

Download

  • SNMP support for monitoring purposes.
  • Multiple status page improvements. A new counter has been added that shows the amount of bytes sent/transmitted over the radio. Counters does now display the current throughput per second in addition to their absolute values.
  • RCS status is now displayed on the status page.
  • RCS communication improvements; communication could fail to restart after being stopped.
  • The absolute signal level displayed on the status paged showed the wrong value. Note, the displayed RSSI value was correct.
  • The Repeatit Discovery Client could fail to detect a Trinity unit when configured to use VLAN.

 

Trinity-100 1.2.3 – 2010-12-03

Download

  • RCS statistics were not recorded properly.
  • The web interface could in certain circumstances fail to show the “Save to flash” button.

 

Trinity-100 1.2.2 – 2010-11-09

Download

  • Antenna selection for dual polarized antennas with the purpose of disabling either the horizontal or vertical polarization did not work as expected.
  • Antenna selection is now displayed as horizontal/vertical for units with built-in antennas.

 

Trinity-100 1.2.1 – 2010-11-03

Download

  • Initial Trinity-100 release.
  • Major performance enhancements that increase the number of pps and radio throughput.
  • Stability improvements; An extremley overloaded link could cause the unit to reboot.
  • Password fields in the web interface are now correctly masked.
  • A unit in master mode could fail to select a channel if auto selection outdoor/indoor was selected together with a regulatory domain that didn’t have any outdoor nor indoor channels.
  • RCS communication improvements; A unit could fail to (re-)connect to the RCS due to communication problems even though the unit was up, resulting in the RCS marking the unit as down.
  • The virtual LEDs in the web interface sometimes failed to render properly.
  • JavaScript fixes for Internet Explorer.
  • An entry that shows link uptime has been added to the status page.

TX rate is now shown by default on the status page.

Latest firmware

Current version is 1.5.0.15:
– Latest Firmware (V1.5.0.15)

Contact us today for pricing, technical support & more info